Car Key Button Repair
A broken car key button is frustrating. This Web page is possible to call the 24 hour Locksmith Service or purchase an alternative remote.
But, you may be in a position to save money by fixing an old key fob rather than replacing it. This is especially true if the problem is caused by the worn-out switch or defective contact.
Battery
If the buttons on the key fob aren't responding to pressing, it could be an obvious sign that the battery is dying or at the end of its lifespan. It's simple to replace the battery on your own instead of hiring a locksmith or dealership.
First, locate the battery compartment. The battery compartment is typically located on the back of the key fob and can be concealed behind a cover that can slide out or an open button that opens the access point. When the compartment is open, look for the small button-cell battery. This is typically shaped like a coin and identified with the plus and minus signs. Remove the battery that is old and replace it with a new one. Make sure the plus and symbol are aligned correctly.
Once the battery is in place Close the compartment and snap the two halves of the key fob. Be sure to align the parts and secure them correctly prior to closing the door and testing your keys. Press any of the buttons to confirm that they function properly.
If your remote keyfob does not work after replacing the battery, there could be other problems that require a different kind of repair. The fob's dropping into a pool of water can cause it to stop functioning. It could also be experiencing an internal electrical failure or it may require to be deprogrammed by an expert or locksmith. Take a look at these other automotive troubleshooting methods to determine whether your key fob may be having a problem of its own.
Switches
Depending on the year and manufacturer, there are various kinds of switches available that are used in the car keyfob. The older model of key often has a separate chip which you can see in the case, while the modern keys are more sophisticated and operate by sending signals to the car. Regardless of the type, the keys' buttons can get worn down or damaged when used regularly. They can become difficult to press or unresponsive. If you press the button too hard it could cause more damage. It may also prevent the key from working in the future.
If your key doesn't seem to be working, you should first try changing the battery. If this doesn't work, you may have to clean your key fob or adjust the switches. Because these tiny electronic switches spend a lot of time getting jostled around they are more prone to break down than the larger components of your key.
The switches are rubber-like and are coated with an electric conductor film that wears down over time. They're fortunately a very small part and inexpensive to replace. They're soldered to the circuit board, which means you need to carefully take them off without damaging any other part of the circuit. Then, you can solder the new ones in and rebuild your key fob.
An effective way to protect your car key fob from becoming ruined is to avoid using it for longer than a couple of hours at a stretch, and to avoid leaving it in areas that it will be visible. When you're not using your key, store it in a secure location.
If you've already tried cleaning your key fob and replacing the battery, but the issue continues to persist, it may be time to think about hiring an appointment with a locksmith. A professional locksmith can test the frequency of your key to see if it's still able to communicate with your vehicle. They can also open and replace micro switches, change cases and more.
Outer Case
If the buttons don't move freely in the case, they may be stuck or even break. If cleaning web page using rubbing alcohol and a cotton swab doesn't work, it might be necessary to remove the case. If the contacts the buttons touch aren't a good fit or if they're worn, changing them might be the only option.
Rubber buttons may wear out over the years. The rubber stretches, nails gouge into it and the buttons can become difficult to press. This can cause the key to fail, and in this case it is time for the replacement of the case or buttons. This repair involves disassembling your remote, locating the button switches on the board, then heating the solder, and then carefully remove them. The new buttons are then connected to the circuit board. The case can be reassembled, and the key blade of the horseshoe can be attached. The new buttons should be snugly fitted inside the case to avoid them falling out.
Inner Case
Since your key fob is prone to be tossed around and sometimes be accidentally pressed and the buttons inside may become stuck or broken over time. With the help of metal tape and a hole-punch, you can solve this issue in the event that your vehicle is not at home and the key fob doesn't work and you are unable to open the doors, but not to start the engine. This quick fix could allow you to safely return to your vehicle to complete your journey.